
From Fluid Kayaks... www.fluidkayaks.co.zaOUTFITTINGFirst of all, please note that two different types of bolts are used on Fluid kayaks:
• The one type is an allen cap bolt, using a 4mm allen key. Under normal circumstances, these should never be adjusted. All allen cap bolts that are screwed into moulded-in inserts are fixed with medium strength loctite. The rest of the allen cap bolts are screwed into nylock nuts to prevent them from loosening.
•The other type of bolt used are slotted bolts, which means they are screwed in and out with a flat screwdriver. These bolts are used for everything that need to be adjusted. The slots in these bolts are wide enough to allow a variety of flat objects, even coins, to be used.
The outfitting is like all things Fluid: simple to use, effective, lightweight. No gimmicks.
Outfitting used in all kayaksAll our kayaks use the same rotomoulded seat system, which is strong and relatively light. These seats offer a huge area of hull support, complete with foam padding underneath the seat. Different sized seats are used for the different size kayaks. The backrest can be adjusted with ratchets mounted on the seat.

The seat is attached to the kayak with plastic wedges, as shown here. The seat has 5 possible positions. We set the seat in the middle position at the factory, which should work fine for most paddlers. It is important to get the trim of the kayak right though. The ideal trim for most paddlers is with the bow about 2cm higher out of the water than the stern.
To move the seat, first loosen the hip pads covering the bolts that hold the seat in place. There are two bolts on each side, so four in total. Then loosen the bolts. For the not-so-technical minded, that means turn them anti-clockwise. Undo each bolt about 15mm. Then use a bit of force to move the seat forward or backward. It is easiest to move one side of the seat first (after all four bolts have been loosened), and then the other side. If the seat is really difficult to move for some reason, put the boat vertical on end, which will make it easier to apply some force. If you want to move the seat backward, put the boat on its stern, and vice versa. Once the seat is moved to the desired location, make sure that the little markers moulded into the top of the seat lines up with the notches on the wedge. Tighten all four bolts properly.

The backrest is kept in place by bungee cords. The rope that attaches the backrest to the ratchets is one long loop, with the two ends joined by a double fisherman’s knot on the backside of the backrest. To make bigger adjustments than what the ratchets allow, simply undo this knot and make a new knot.
As can be seen here, all seats are also fitted with two loops at the back, one on each side, to which any loose items like throw bags, dry bags and buoyancy bags can be attached.

The thigh braces are solid, comfortable, and easy to adjust. Simply undo the two bolts shown here, and take the bolts out completely. Do not loosen the third bolt situated in the cockpit groove. Once the two bolts shown are removed, slide the thigh brace forwards or backwards to the desired position. Line up the holes in the cockpit with the threaded holes in the brass inserts, which are moulded into the thigh braces, and screw the bolts back in.

The powder-coated die-forged aluminium handles are strong, durable and easy on the hands.

All our kayaks come standard with a drain plug.
Nemesis, Element, Spice and Flirt specific outfittingAll our kayaks, except for the Solo series, have closed cell foam pillars in the bow and stern.

The footblock system consist of closed cell foam blocks, cut to size, which are supplied in the goodie bag. The foam blocks fit together like shown below. Use as many blocks as you need to get your feet comfortable. The idea is to get as much pressure off your toes by supporting the heels. If necessary, cut the foam blocks to get the perfect fit. Once the setup is worked out, simply glue these pieces of foam together with contact adhesive. It takes a bit of effort to get it perfect, but if done properly, your feet will thank you.
Solo specific outfittingThe Solos have a unique plastic rib cage in the bow and stern, with a step-out platform in the bow. The rib cage gives ultimate support to make sure your Solo keeps its shape, even in extreme conditions like pins under water.

The plastic footblocks are easily adjusted by means of aluminium rails and plastic knob nuts.

The plastic footblocks have a dual layer foam system to give the feet firm support but still absorb impact.

The Solos are supplied with an extra, bigger footblock to be used by shorter paddlers. The bow of a kayak is tapered, which means that if a short paddler would pull back the standard footblock too far, a gap will be formed around the footblock that can trap one’s foot in the case of a pin. It is therefore advised that short paddlers take the standard footblock out, undo the bolts and nuts by which the aluminium rails are attached to the footblock, and fix the bigger footblock to the rails as shown here.
Goodie bagAll our kayaks are supplied with a mesh goodie bag, as shown below. Inside the goodie bag a variety of items will be found, which are listed below together with their applications.

A sponge in the shape of Africa.

A Fluid water bottle.

Hip pad shims together with double-side velcro pieces. Add these shims underneath the hip pads if needed. The ideal is to be as tight as possible in your kayak, without creating pressure points that hurts. To add a shim, simply loosen the webbing that holds the hip pad in place, stick a piece of velcro to the shim, and then slide the shim into the gap between the hip pad and seat.


Extra thigh brace pads. The thigh braces are already fitted with exactly the same pads, but some paddlers prefer to lower the thigh brace surface to create a tighter fit. Use contact adhesive to glue the pads to the braces.


Patella pads. If you are one of those paddlers with sensitive knees, use contact adhesive to glue these pads to the inside of the sidewall of the kayak, underneath and slightly forward of the thigh braces. Make sure the pads are in the correct position by climbing into your kayak first to check, before gluing the pads.


Extra seat pad, for paddlers who prefer to raise the seat for extra leverage. A tip: the seat will look neater if you glue this underneath the nice looking thermo-formed pad that is already on your seat, instead of on top. The thermo-formed pad is glued to the seat, but with care it can be removed. Glue the extra seat pad onto the seat with contact adhesive, and then re-glue the thermo-formed pad on top of it.

Warranty registration card. Fill it in and post it to Fluid. But you can also register online on our website if you prefer.

Some Fluid stickers. You know what to do with them.
WakaWai.com